Installing Memory

background image

Installing Memory

Your Mac Pro comes with a minimum of 3 GB of memory in the single-processor
model, or a minimum of 6 GB of memory in the dual-processor model, installed as
1 GB unbuffered ECC dual inline memory modules (UDIMMs).
All installed UDIMMs must meet these specifications:

PC3-10600E, 1333 MHz, DDR3 SDRAM UDIMMs

Error-correcting code (ECC)

72-bit wide, 240-pin ECC modules

36 ICs maximum per ECC UDIMM

NOTICE:

Apple recommends that you use Apple-approved DIMMs. DIMMs from older

Mac computers cannot be used in your Mac Pro. You can purchase Apple-branded
memory online from the Apple Store at www.apple.com/store.

When purchasing DIMMs for use in Mac computers, make sure that the memory vendor
conforms to the Joint Electron Device Engineering Council (JEDEC) specification. Check
with your memory vendor to ensure that the DIMMs support the correct timing modes
and that the Serial Presence Detect (SPD) feature has been programmed properly, as
described in the JEDEC specification.

Note: Although the memory speed of the UDIMMS is 1333 MHz, they will operate at
1066 MHz or 1333 MHz depending on the processor in the computer.

background image

44

Chapter 3

Making a Good Thing Better

Before you install memory, determine whether you have a single- or dual-processor
Mac Pro. Remove the side panel, following the instructions in “Opening Your Mac Pro”
on page 39, and look inside:

A quad-core or 6-core Mac Pro has one processor and four memory slots. You can
install a total of up to 16 GB of memory. See “Installing Memory in a Quad-Core or
6-Core Mac Pro” on page 45.

An 8-core or 12-core Mac Pro has two processors and eight memory slots. You can
install a total of up to 32 GB of memory. See “Installing Memory in an 8-Core or
12-Core Mac Pro” on page 54.

One processor

Two processors

background image

45

Chapter 3

Making a Good Thing Better

You can also determine which Mac Pro you have by choosing Apple () > About This
Mac from the menu bar. Click More Info, choose Hardware from the Contents list, and
then find Number Of Processors in Hardware Overview. The quad-core and 6-core
Mac Pro have one processor and the 8-core and 12-core Mac Pro have two processors.

Installing Memory in a Quad-Core or 6-Core Mac Pro

The quad-core and 6-core Mac Pro have four memory slots, and come with at least
three 1 GB DIMMs installed. You can replace or install additional 1 GB, 2 GB or 4GB
DIMMs for a total of up to 16 GB of memory.

It s important that all DIMMs installed in your Mac Pro are of the correct specifications.
Use the instructions that follow to install DIMMs in a quad-core or 6-core Mac Pro.

To install memory:

1

Shut down your Mac Pro, open it, and remove the side panel, following the instructions
in “Opening Your Mac Pro” on page 39.

WARNING:

Let your Mac Pro cool down for 5 to 10 minutes before you remove the

processor tray or touch the internal components. The processor tray and components
may be very hot.

background image

46

Chapter 3

Making a Good Thing Better

2

Push the latches on the processor tray until they partially open.

Latches

background image

47

Chapter 3

Making a Good Thing Better

3

Pull the latches until they open all the way and release the processor tray.

background image

48

Chapter 3

Making a Good Thing Better

4

Remove the processor tray and lay it on a soft, clean cloth on the desk or work surface,
to protect the tray and avoid scratching the work surface.

Processor tray

background image

49

Chapter 3

Making a Good Thing Better

If you install equal-size DIMMs (for example, all 1 GB DIMMS or all 2 GB DIMMS) in your
quad-core or 6-core Mac Pro, Apple recommends that you fill the slots in the order
listed in the table.

Slot 4

Slot 3

Slot 2

Slot 1

If you have

Fill these slots

Two DIMMs

1 and 2

Three DIMMs

1, 2, and 3

Four DIMMs

1, 2, 3, and 4 (all)

Note: If you install different-size DIMMs in your Mac Pro, follow the order in the table.
If the DIMM configuration you install doesn t provide optimized performance, the
Memory Slot Utility appears onscreen and recommends an improved configuration.

To use the utility again, go to /System/Library/CoreServices/Memory Slot Utility.

background image

50

Chapter 3

Making a Good Thing Better

5

Open the ejectors on DIMM slots 1, 2, and 3 and push them out to the sides. Then
remove the DIMMs from the slots.

6

Install the DIMMs by aligning them in the DIMM slots and pushing both ends of the
DIMM down until the tabs are vertical and the ejectors snap into place.

NOTICE:

To avoid damaging the DIMM, hold it by the corners and don t touch the

gold connectors or other components.

Ejectors

Notch

Connectors

background image

51

Chapter 3

Making a Good Thing Better

7

Reinstall the processor tray, pushing it in until the latches are at a 90-degree angle.

Processor tray

Latch

8

Push the latches all the way in to close them and seat the processor tray.

background image

52

Chapter 3

Making a Good Thing Better

9

Replace the side panel.
When you replace the side panel, make sure the latch is up. Hold the side panel
securely so it stays in place as you push the latch down.

Place the side panel
in the slot and then
push to close.

NOTICE:

Always replace the side panel after installing components. Your Mac Pro

doesn t operate properly without the side panel in place.

background image

53

Chapter 3

Making a Good Thing Better

10

Hold the side panel against your Mac Pro and push the latch down to secure the
side panel.

You can attach a lock or cable through a metal loop (under the latch) to secure your
Mac Pro. Flip the metal loop down before you close the latch, then close the latch and
attach your lock or cable through the extended loop.

background image

54

Chapter 3

Making a Good Thing Better

Installing Memory in an 8-Core or 12-Core Mac Pro

The 8-core and 12-core Mac Pro have eight memory slots, and, in most configurations,
come with at least six 1 GB DIMMs installed. You can install a total of up to 32 GB
of memory.

It s important that all the DIMMs installed in your Mac Pro have the correct specifications.
Use the instructions that follow to install DIMMs in an 8-core or 12-core Mac Pro.

To install memory in a dual-processor Mac Pro:

1

Shut down your Mac Pro, open it, and remove the side panel, following the instructions
in “Opening Your Mac Pro” on page 39.

WARNING:

Let your Mac Pro cool down for 5 to 10 minutes before you remove the

processor tray or touch the internal components. The processor tray and components
may be very hot.

background image

55

Chapter 3

Making a Good Thing Better

2

Push the latches on the processor tray until they open slightly.

Latches

background image

56

Chapter 3

Making a Good Thing Better

3

Pull the latches until they open all the way and release the processor tray.

background image

57

Chapter 3

Making a Good Thing Better

4

Remove the processor tray and lay it on a soft, clean cloth on the desk or work surface,
to protect the tray and avoid scratching the work surface.

Processor tray

background image

58

Chapter 3

Making a Good Thing Better

If you install equal-size DIMMs (for example, all 1 GB DIMMS or all 2 GB DIMMS) in your
8-core or 12-core Mac Pro, Apple recommends that you fill the slots in the order listed
in the table.

Slot 4

Slot 3

Slot 2

Slot 1

Slot 5

Slot 6

Slot 7

Slot 8

If you have

Fill these slots

Two DIMMs

1 and 2

Three DIMMs

1, 2, and 3

Four DIMMs

1, 2, and 5, 6

Six DIMMs

1, 2, 3, and 5, 6, 7

Eight DIMMs

1, 2, 3, 4, and 5, 6, 7, 8 (all)

background image

59

Chapter 3

Making a Good Thing Better

Note: If you install different-size DIMMs in your Mac Pro, follow the order in the table.
If the DIMM configuration you install doesn t provide optimized performance, the
Memory Slot Utility appears onscreen and recommends a better configuration.

To use the utility again, go to /System/Library/CoreServices/Memory Slot Utility.

5

Install the DIMMs by aligning them in the DIMM slots and pushing both ends of the
DIMM down until the tabs are vertical and the ejectors snap into place.

NOTICE:

To avoid damaging the DIMM, hold it by the corners and don t touch the

gold connectors or other components.

Ejectors

Notch

Connectors

background image

60

Chapter 3

Making a Good Thing Better

6

Reinstall the processor tray, pushing it in until the latches are at a 90-degree angle.

7

Push the latches all the way in to close them and seat the processor tray.

Processor tray

Latch

8

Replace the side panel, following the instructions starting on page 52.

NOTICE:

Always replace the side panel after installing components. Your Mac Pro

doesn t operate properly without the side panel in place.

background image

61

Chapter 3

Making a Good Thing Better