Installing Internal Storage Devices

background image

Installing Internal Storage Devices

Your Mac Pro has room for six internal drives: two optical drives, and four hard disk or
solid state drives. In most configurations, a single drive occupies the first drive bay and
an optical drive is located in the upper optical drive bay.

You can add up to three 3.5-inch cable-free Serial ATA (SATA) hard disk drives to the
empty drive bays. The drives must meet these specifications:

Type: SATA 3 Gb/s

Width: 3.9 inches (102 mm)

Depth: 5.7 inches (147 mm)

Height: 1.0 inch (25.4 mm)

You can add up to three 2.5-inch solid state disk drives (SSDs) to the empty drive bays.
The drives must meet these specifications:

Type: SATA 3 Gb/s

Width: 2.5 inches (63.5 mm)

The solid state drives (SSD) come with adapters that fit the 3.5-inch drive bays.

For more information about requirements or supported devices, visit an Apple
Authorized Reseller, the Apple Store at www.apple.com/store, or the Mac Pro Support
website at www.apple.com/support/macpro.

background image

62

Chapter 3

Making a Good Thing Better

Installing Serial ATA Hard Disk Drives

Your Mac Pro can accommodate up to four internal 1-inch-high SATA hard disk drives
in the drive bays. If your Mac Pro comes with a single drive installed, it s in the first drive
bay. You can install drives in the second, third, and fourth drive bays.

To install a hard disk drive:

1

Open your Mac Pro and remove the side panel following the instructions in “Opening
Your Mac Pro” on page 39.

2

Lift the latch to unlock the drive carriers.
Note: When the latch is down, the carriers are locked in the drive bays and can t
be removed.

3

Pull the carrier out of the drive bay.

Drive carrier

background image

63

Chapter 3

Making a Good Thing Better

4

Position the carrier over the hard disk drive with the connectors at the back.

5

Use the four screws on the carrier to attach the hard disk drive to the carrier.

NOTICE:

Hold the drive by its sides. To avoid damaging the drive, don t touch the

printed circuit board.

Connectors

background image

64

Chapter 3

Making a Good Thing Better

6

Lift the latch and slide the carrier over the guides and into the drive bay until it s
touching the drive connectors and is seated in the bay.

Drive
connectors

7

Replace the side panel, following the instructions starting on page 52.

NOTICE:

Always replace the side panel after installing components. Your Mac Pro

doesn t operate properly without the side panel in place.

background image

65

Chapter 3

Making a Good Thing Better

Installing a Solid State Drive

Your Mac Pro can accommodate up to four internal 2.5-inch solid state drives in the
drive bays. If your Mac Pro comes with a single drive installed, it s in the first bay. You
can install drives in the second, third, and fourth drive bays.

To install a solid state drive:

1

Open your Mac Pro and remove the side panel, following the instructions in “Opening
Your Mac Pro” on page 39.

2

Lift the latch to unlock the drive carriers.
Note: When the latch is down, the carriers are locked in the drive bays and can t
be removed.

3

Pull the carrier out of the drive bay.

Drive carrier

background image

66

Chapter 3

Making a Good Thing Better

4

Remove the two screws from the drive carrier as shown. You ll attach the SSD adapter
to the carrier using the two remaining screws. Put the two screws that you removed
away for safekeeping.

Connectors

Hooks

Screws

Unused screws (2)

5

Position the drive carrier over the SSD adapter with the drive connectors at the back as
shown. Insert the two hooks on the top of the adapter into the carrier s holes. Fasten
the two screws on top of the carrier to attach the SSD enclosure to the carrier.

background image

67

Chapter 3

Making a Good Thing Better

6

Lift the latch and slide the carrier over the guides and into the drive bay until it touches
the drive connectors and is seated in the bay.

Drive
connectors

7

Replace the side panel, following the instructions starting on page 52.

NOTICE:

Always replace the side panel after installing components. Your Mac Pro

doesn t operate properly without the side panel in place.

background image

68

Chapter 3

Making a Good Thing Better

Replacing an Optical Drive

Your Mac Pro comes with one or two SuperDrives installed in the optical drive bays.
Follow these instructions to replace an optical drive.

Note: Contact your drive manufacturer or consult the manufacturer s website to
determine if your drive is set to cable select mode. Before you install a drive, set the
drive to cable select mode if the manufacturer hasn t already done so.

To replace the optical drive:

1

Open your Mac Pro and remove the side panel, following the instructions in “Opening
Your Mac Pro” on page 39.

2

Lift the latch to unlock the optical drive carriers.
When the latch is down, the drives and carriers are locked in the optical drive bays and
can t be removed.

background image

69

Chapter 3

Making a Good Thing Better

3

Pull the carrier halfway out of the optical drive bay.

background image

70

Chapter 3

Making a Good Thing Better

4

Disconnect the cable from the optical drive and remove the carrier from the optical
drive bay.

NOTICE:

When you install or replace optical drives, use the original Apple cables that

came with your Mac Pro.

background image

71

Chapter 3

Making a Good Thing Better

5

Remove the optical drive from the carrier by unscrewing the four attachment screws.

6

Use the four screws from the original optical drive to attach the replacement drive to
the carrier.

background image

72

Chapter 3

Making a Good Thing Better

7

Slide the optical drive and carrier over the guides halfway into the optical drive bay.

8

Attach the cable to the back of the optical drive.

Cable middle
connector

Cable end
connector

background image

73

Chapter 3

Making a Good Thing Better

9

Lift the latch and then slide the carrier into the optical drive bay, pushing it into place.

10

Replace the side panel, following the instructions starting on page 52.

NOTICE:

Always replace the side panel after installing components. Your Mac Pro

doesn t operate properly without the side panel in place.

background image

74

Chapter 3

Making a Good Thing Better